UNIQUE HARDWARE CO., LTD. DIGIPHONE 34F Card Type Modem (synchronous/asynchronous) Chipset Unidentified I/O Options Voice, speakerphone, DSVD Maximum Data Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34 Rockwell V.FC Fax Modulation ITU-T V.17, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I & II Data Bus Serial [Image] CONNECTIONS Function Label Function Label DC power in CN1 Telephone line in CN4 Serial port CN2 Power switch SW1 Telephone line out CN3 DIAGNOSTIC LED(S) LED Color Status Condition TM/FAX Green On Modem is connected in FAX mode TM/FAX Green Blinking Modem is in test mode TM/FAX Green Off Modem is not connected in FAX mode 288 Green On Modem connected at 28.8Kbps 288 Green Off Modem connected at slower than 28.8Kbps 144 Green On Modem connected at 14.4Kbps or faster 144 Green Off Modem connected at slower than 14.4Kbps 24 Green On Modem connected at 2400bps or 1200bps 24 Green Off Modem not connected at 2400bps or 1200bps EC Green On Error correction enabled EC Green Off Error correction disabled DIAGNOSTIC LED(S) (CON'T) LED Color Status Condition AA Green On Auto-answer enabled AA Green Off Auto-answer disabled AA Green Blinking Phone is ringing CD Green On Carrier signal detected CD Green Off Carrier signal not detected OH Green On Modem is off-hook OH Green Off Modem is on-hook OH Green Blinking Modem is dialing in pulse mode SD Green On Modem is transmitting data SD Green Off Modem is not transmitting data RD Green On Modem is receiving data RD Green Off Modem is not receiving data TR Green On DTR signal is high TR Green Off DTR signal is low PWR Green On Power is on PWR Green Off Power is off SUPPORTED STANDARD COMMANDS Basic AT Commands +++, ‘comma’, A/ A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z &C, &D, &F, &G, &K, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z Extended AT Commands \A, \B, \G, \K, \L, \N %C, %E, %L, %Q Special AT Commands #CID, +MS S-Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S26 S27, S29, S30, S31, S32, S33, S36, S38, S40, S41, S46, S48, S82, S86, S95 Note: See MHI help file for complete information. Proprietary AT Command Set DISPLAY CHIPSET MANUFACTURER Type: Immediate Format: AT [cmds] #MFR? [cmds] Description: Displays the voice chipset manufacturer’s name. DISPLAY CHIPSET MODEL NAME Type: Immediate Format: AT [cmds] #MDL? [cmds] Description: Displays the model name of the modem's voice chipset. DISPLAY CHIPSET REVISION Type: Immediate Format: AT [cmds] #REV? [cmds] Description: Displays the revision level of the modem's voice chipset. DSVD MODE Type: Configuration Format: AT [cmds] -SSE=n [cmds] Description: Select whether the modem will use DSVD mode. Command Function -SSE=0 DSVD mode disabled. -SSE=1 DSVD mode enabled. MODE SELECTION Type: Immediate Format: AT [cmds] #CLS=n [cmds] Description: Selects which mode the modem will operate in. Command Function #CLS=0 Modem will operate in data mode. #CLS=1 Modem will operate in fax class 1 mode. #CLS=2 Modem will operate in fax class 2 mode. #CLS=8 Modem will operate in voice mode. TONE DETECTION Format: AT [cmds] #VTD=x,y,z [cmds] Default: x,y,z 3F Range: 0 - 3F (hexadecimal) Description: Sets which tones the tone detection will report. Note: The value of x sets the tone detection modes in voice transmit mode, y sets them in voice receive mode, and z sets them in voice command mode. Bit Value Function 0 0 DTMF tones are not detected. 1 DTMF tones are detected. 1 0 V.25 1300Hz calling tone is not detected. 1 V.25 1300Hz calling tone is detected. 2 0 T.30 1100Hz fax tone is not detected. 1 T.30 1100Hz fax tone is detected. 3 0 V.25/T.30 2100Hz answer tone is not detected. 1 V.25/T.30 2100Hz answer tone is detected. 4 0 Bell 2225Hz answer tone is not detected. 1 Bell 2225Hz answer tone is detected. 5 0 Call progress tones are not detected. 1 Call progress tones are detected. TONE GENERATOR - DIRECT ENTRY Type: Immediate Format: AT [cmds] #VTS=[m, n, x] Range: m 200-3000, n 200-3000, x 0-255 Unit: m 1 Hz, n 1 Hz, x .1 second Description: Generates a dual-frequency tone for duration x at frequencies m and n. TONE GENERATOR - TIMED PHONE KEYS Type: Immediate Format: AT [cmds] #VTS={a, n} Range: a 0-9, A-D, #, *; x 0-255 Unit: n .1 second Description: Generates the DTMF tone for duration x for the character a. TONE GENERATOR - PHONE KEYS Type: Immediate Format: AT [cmds] #VTS=a Range: 0-9, A-D, #, * Description: Generates the DTMF tones for the characters in the string for the duration set with +VBT. TONE GENERATOR LENGTH Format AT [cmds] #VBT=n [cmds] Default: 10 Range: 0 - 40 Unit: 0.1 second Description: Sets the length of DTMF tones that are generated. VOICE BUFFER SPACE Type: Configuration Format: AT [cmds] #VSK=n [cmds] Default: 255 Range: 0 - 255 Unit: 1 byte Description: Sets the amount of data the modem can send into the buffer after the XOFF signal is sent. VOICE DEVICE Type: Configuration Format: AT [cmds] #VLS=n [cmds] Description: Selects the I/O device for the DSP chip. Command Function #VLS=0 Telephone line and handset used for voice I/O. #VLS=1 Telephone handset used for voice I/O. #VLS=2 Internal speaker only used for voice I/O. #VLS=3 External microphone only used for voice I/O. #VLS=4 Telephone line and handset used for voice I/O; internal speaker enabled. #VLS=5 Headset used for voice I/O. #VLS=6 Speakerphone used for voice I/O. #VLS=7 Handset muted by disconnecting handset or speakerphone from telephone line. #VLS=8 Connects caller ID relay for recording of conversation over handset. #VLS=9 Connects handset (or speakerphone) to DSP chip for recording or playback. VOICE - DISPLAY BUFFER SIZE Type: Immediate Format: AT [cmds] #VBQ? [cmds] Description: Displays the size of the voice buffer. VOICE - DISPLAY COMPRESSION TYPE Type: Immediate Format: AT [cmds] #VCI? [cmds] Description: Displays the type of compression currently in use. VOICE - LOCAL SERIAL PORT SPEED Type: Configuration Format: AT [cmds] #BDR=n [cmds] Default: 0 Range: 0 - 48 Unit: 2400bps Description: Sets the speed of the local serial port when in voice mode. A value of 0 indicates that the modem should auto-detect the correct serial port speed. VOICE RE-RING DETECT TIME Type: Configuration Format: AT [cmds] #VRA=n [cmds] Default: 70 Range: 0-255 Unit: 10 mS Description: Sets the maximum time the modem will wait for the remote station to ring again before it assumes that it has gone off-hook. VOICE RECEIVE Type: Immediate Format: AT [cmds] #VRX Description: Commands the modem to begin receiving voice data. VOICE RING DETECT TIME Type: Configuration Format: AT [cmds] #VRN=n [cmds] Default: Unidentified Range: Unidentified Unit: Unidentified Description: Sets the maximum time the modem will wait for the remote station to ring before it assumes that it went off-hook before it rang. VOICE SAMPLE QUALITY Type: Configuration Format: AT [cmds] #VBS=n [cmds] Description: Selects the number of bits per sample that the modem records. Command Function #VBS=2 Modem records 2 bits per sample in ADPCM encoding. #VBS=4 Modem records 4 bits per sample in ADPCM encoding. #VBS=8 Modem records 8 bits per sample in PCM encoding. VOICE SAMPLING RATE Type: Configuration Format: AT [cmds] #VSR=n [cmds] Description: Sets the sampling rate used when recording voice signals. Command Function #VSR=7200 Selects a sampling rate of 7.2KHz. #VSR=11025 Selects a sampling rate of 11.025KHz in PCM encoding only. VOICE SILENCE DETECTION TIME Type: Configuration Format: AT [cmds] #VSP=n [cmds] Default: Unidentified Range: 0 - 255 Unit: .1 second Description: Sets the minimum amount of silence that the modem will detect. VOICE SILENCE DETECTION THRESHOLD Type: Configuration Format: AT [cmds] #VSS=n [cmds] Description: Sets the threshold of sensitivity that the modem uses to determine silence detection. Command Function #VSS=0 Silence detection disabled. #VSS=1 Minimum silence detection sensitivity. #VSS=2 Standard silence detection sensitivity. #VSS=3 Maximum silence detection sensitivity. VOICE TIMING MARK Type: Configuration Format: AT [cmds] #VTM=n [cmds] Description: Configures timing mark placement. Command Function #VTM=0 Timing marks disabled. #VTM=10 Timing marks enabled at 1 second intervals. VOICE TRANSMISSION LEVEL Type: Configuration Format: AT [cmds] #TL=hhhh [cmds] Default: 3F44 for phone line, 7FFF for handset or speaker Range: 0000 - 7FFF Unit: Unidentified (hexadecimal) Description: Sets the transmission level for sending audio in voice mode. VOICE TRANSMIT Type: Immediate Format: AT [cmds] #VTX Description: Commands the modem to begin transmitting voice data. VOICE VOLUME LEVEL Type: Configuration Format: AT [cmds] #VGT=n [cmds] Default: 153 Range: 128 - 228 Unit: Unidentified Description: Sets the volume level when playing back audio signals. See UNIQUE HARDWARE, INC. FAXSENGER 34 for a full command summary.